6ES5482-8MA13 - Digital I/O Module - SIEMENS Expand

6ES5482-8MA13 - Digital I/O Module - SIEMENS

SIEMENS SIEMENS

Refurbished

This SIEMENS input/output module reference 6ES5482-8MA13 is part of the SIMATIC S5 range. ET-100U.

SIMATIC S5 482 NON-FLOATING DIGITAL INPUT / OUTPUT MODULE FOR PLC AND-100U / F 16 INP./16 OUTP. 24 VDC; READING AND SWITCHING

This SIEMENS digital module is at your disposal in supply to replace your defective equipment and has a guarantee adapted to your needs.

More details

In stock, shipping within 24h.

50,00 €

livraison-2.pngQuick delivery

garantis2.pngWarranted systems

paiement-securise-SEI_1.jpgSecure Payment 


Product options

standard exchange refurbished

Standard exchange service

Reconditioned and tested systems
6 to 12 months warranty

new systems

Standard exchange service

New systems
12 to 24 months warranty

supply refurbished

Supply service

Reconditioned and tested systems
6 to 12 months warranty

supply new

Supply service

New systems
12 to 24 months warranty

supply in the state

Supply service

Systems sold in the state
without warranty

The modular ET 100U electronic terminator for distributed I/O extends the I/O range of compact programmable controllers.

The extra-discrete modularity of the ET 100U makes it the ideal solution for plants and machines where sensors and actuators are distributed over a large area.

Input and output modules for all commonly used (digital) signal levels and for all the usual (analog) signal ranges can be used. With 1, 2, 4 or 8 channels, these modules can be combined up to the maximum configuration (32 bytes) in any mix. The modules exchange information with the relevant 318-8 interface module via a modular bus consisting of bus units.

The ET 100U stations (maximum of 31 stations) exchange information with the higher-level central controller via a shielded two-wire cable and the 308-3 and 318-8 interface modules. The baud rate can be anything up to 375,000 bps. The 308-3 interface module is the master and controls message traffic.

A dual-port RAM is available as a buffer for data traffic between the SIMATIC S5 processor and the 308-3 interface module. The dual-port RAM has 2K bytes - 1K byte each for inputs and outputs. The central processor accesses the ET 100U using the STEP 5 load and transfer operations. The central processor and the 308-3 interface module operate asynchronously and therefore do not interfere with each other.

The I/O modules have no address setters. The relevant module addresses are stored in an EPROM in the 308-3 interface module and transferred to the indi- vidual ET 100Us at every start-up or restart.
The corresponding address lists are generated on the programmer with the help of the COM ET 100 software.

Diagnostics capabilities simplify operation and troubleshooting in the system. In addition to the error and fault displays on the modules, all error and fault information is stored according to error type in diagnostics bytes and can be read out via the programmer, displayed on output modules or on screen via a standard interface, or printed out.

Height 13,5 cm / 5,4 in
Width 4,5 cm / 1,7 in
Length 10 cm / 3,9 in
Weight 0,1 kg / 0,2 lb
Family SIMATIC S5
Reference 6ES5482-8MA13

If Service exchange, thank you describe below the defect found on your defective part.
Allowed file formats are: GIF, JPG, PNG

loader

* required fields

No customer reviews for the moment.

Write a review

Siemens is an international group of German origin specializing in high technology and present in the sectors of industry, energy and health. It was founded in 1847 by Werner von Siemens.

Accept

On this site, we use tools that store cookies on your device. Cookies are used to enable the site to function properly, to generate statistical reports and to advertise our services / products. With these cookies, you help us to offer you a better user experience.