A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC
A06B-6050-H103 - Velocity Control Unit  - FANUC

A06B-6050-H103 - Velocity Control Unit - FANUC

A06B-6050-H103

This FANUC velocity control unit is reference A06B-6050-H103. AC drive for FANUC Model 10 type axis motor.

This FANUC velocity control unit is at your disposal to replace your defective equipment and has a guarantee adapted to your needs.

FANUC system reconditioned and tested on bench manufacturer (Test 100%).

In stock, ready to ship.
State
  • Refurbished Service Exchange
  • Refurbished Supply
Warranty
€600.00

System options

Exchange service with a refurbished unit

Standard Exchange Service

Reconditioned and tested systems

From 6 to 12
month warranty

Exchange service with a new unit

Standard Exchange Service

New systems

From 12 to 24
month warranty

Supply of a refurbished unit

Supply Service

Reconditioned and tested systems

From 6 to 12
month warranty

Supply of a new unit

Supply Service

New systems

From 12 to 24
month warranty

For parts only

Supply Service

Sold for parts – no warranty

Repair

Repair service

Repair will be made to damaged and defectiv units

From 3 to 18
month warranty

Livraison rapide

Fast
delivery

Livraison rapide

guaranteed
products

Livraison rapide

Secure
payment

 

The AC servo unit consists basically of the velocity control unit and power transformer. In addition, the separate regenerative discharge unit may be required according to the load conditions.
Eight types of velocity control units are available according to AC servo motor models employed, and one velocity control unit applies to each servo motor.
Six types of power transformers are also prepared according to the servo motor models, theirs combinations, loads, and primary input voltages.
One power transformer applies to one to three servo motors.

The Ac servo unit for 2 axes consists of the velocity control unit and power transformer. Three types of velocity control units are available according to the combations of AC servo models employed. One velocity control unit applies to two servo motors. The speccifications of the power transformer are the same as those of a power transformer employed when two servo units for one axis are used according to the combinations of motor models.

The AC servo servo unit for 3 axes consists of the velocity contorl unit, the power transformer and the discharge unit.
Four types of velocity control unit are available according to the combinations of the AC servo motor models employed. 
One velocity control unit applies to three servo motors.
One power transformer is employed according to the combiantions of motor model.
A regenerative discharge unit is a resistor unit which consules the regenerated energy by the motor.
If the AC servo motor models employed are rather small type having a little regenerative energy, a regenerative discharge unit may be necessary.

Height
20 cm / 7.8 in
Width
16 cm / 6,2 in
Length
45 cm / 17,7 in
Weight
9 kg / 19.8 lbs
Family
CONTROL UNIT FANUC
Reference
A06B-6050-H103
Refurbished
3005982525593
300334271160

FANUC is a Japanese manufacturer of industrial robots, machining centers and numerical controls for machine tools

Since its creation in 1956, when the company’s founder, Dr. Seiuemon Inaba, introduced the concept of digital controls, FANUC has always been at the forefront of manufacturing techniques in the world. Moving from the automation of a single machine in the late 1950s to the automation of entire production lines over the following decades.

12 other products in the same category: