Leave us a message.


Sorry, we are not available at the moment. Send us a message and we will get back to you soon.

Leave us a message.
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT
TVD 1.2-15-03 - Power Supply Module - INDRAMAT

TVD 1.2-15-03 - Power Supply Module - INDRAMAT

TVD 1.2-15-03

This INDRAMAT TVD 1.2-15-03 power supply module is designed for INDRAMAT CNC machine tools. It is part of the TVD - INDRAMAT range.

Power input: 3x380 ... 460V AC, average current: 7.5A, power: 15kW.

This INDRAMAT TVD 1.2-15-03 power supply module is at your disposal to replace your defective equipment and a suitable guarantee.

In stock, ready to ship.
State
  • Refurbished Service Exchange
  • Refurbished Supply
Warranty
€910.00
VAT excluded

System options

Exchange service with a refurbished unit

Standard Exchange Service

Reconditioned and tested systems

From 6 to 12
month warranty

Exchange service with a new unit

Standard Exchange Service

New systems

From 12 to 24
month warranty

Supply of a refurbished unit

Supply Service

Reconditioned and tested systems

From 6 to 12
month warranty

Supply of a new unit

Supply Service

New systems

From 12 to 24
month warranty

For parts only

Supply Service

Sold for parts – no warranty

Repair

Repair service

Repair will be made to damaged and defectiv units

From 3 to 18
month warranty

Livraison rapide

Fast
delivery

Livraison rapide

guaranteed
products

Livraison rapide

Secure
payment

 

The power rectifier in the power supply module converts the AC line voltage and provides a DC bus voltage for supplying power to the drives. When the drives are operating as generators, the regenerated energy is either fed back into the electrical power system or it is absorbed by a bleeder resistor.
The signal voltage is supplied to all the drives via a wire-ribbon cable.
The power supply module is equipped with an extensive array of monitoring functions. It communicates with the drives by means of the wire-ribbon cable. In the event of trouble, the supply of power to the drives is cut off.

The power supply modules are designed to be operated with modular INDRAMAT AC drives. Modular AC drives can be used for continuous mechanical power requirements up to 24 kW. The appropriate power supply unit is available for all drive requirements within this power range.

The TVD is available in two power levels. It can be used to supply power to main and servo drives having an overall continuous mechanical power output of either 6 kW or 12 kW.
The TVD can be connected directly to 380 ... 460 V, 50 ... 60 Hz three-phase power systems without the need for transformers. A power protection circuit is built in to isolate the drive equipment from the AC power system.
A soft-start circuit in the TVD prevents high inrush current spikes so that the line connection protection devices do not need to be oversized. Line connec- tions can be protected by circuit breakers or slow-blow fuses. Semiconductor- type circuit protection devices are not needed.
The TVD DC bus voltage is regulated so that variations in the line voltage have no effect on drive dynamics. In many cases this permits higher drive speeds to be achieved.
The TVD is always operated with a line filter. Thus, it causes virtually no line reaction. The NAM line conditioning module makes the TVD and the neces- sary filter components easy to install.
When the drives are running in generator mode, the regenerated energy is absorbed by a bleeder resistor. The TVD may be combined with the TBM 1.2 Auxiliary Bleeder Module to increase the continuous and peak regenerated power rating.
TCM 1 Auxiliary Capacitance Modules can be connected to the TVD. When the drives are being braked, the drive energy is stored in the DC bus so that it can be reused for acceleration. Heat losses in the enclosure and energy consumption are therefore minimal. Approximately 30 Ws can be stored per mF auxiliary capacitance.
A dynamic braking feature is provided on the TVD so that motors whose field is produced by a permanent magnet can even be braked if a fault occurs in the drive electronic system. If there is trouble in the drive electronic system or in the system installation (feedback line), the dynamic braking feature is acti- vated by the ready-state contact (Bb) on the TVD, causing the drives to brake to a stop.
The signal voltage is supplied to all drives via a wire-ribbon cable. In the event of a power failure, the electronic circuitry is supplied with power from the DC bus. The drives can therefore be stopped under velocity or position regulation when power failures occur. The line connections for supplying power to the drives and to electronic circuits are jumpered on the unit. Thus, an additional line connection for supplying power to the electronic circuits is not required.
The TVD is equipped with an extensive range of monitoring functions. It communicates with the drives by means of the wire-ribbon cable. Monitored parameters include: motor feedback, current and temperature of the drives, the load on the bleeder resistor, and line voltage. If trouble is encountered, the ready-state contact on the TVD causes the power supplied to the drives to be shut off immediately. LED displays provide for rapid trouble shooting.

Height
39 cm / 15,3 in
Width
32 cm / 12,5 in
Length
15 cm / 5,9 in
Weight
15 kg / 33 lbs
Family
TVD - INDRAMAT
Reference
TVD 1.2-15-03
Refurbished
3006438080857
300309666342

Indramat is an industrial company founded in 1958, based in Neuwied, Germany.
Indramat Gmbh , which is now part of Bosch Rexroth , was an industrial control company founded in 1958, based in Neuwied (am Rhein), Germany. Its name is a German abbreviation meaning «Gesellschaft zur IND ustrialisierung- RA tionalisierung und Auto MAT isierung».

16 other products in the same category: