CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA
CPS-150F - Power Supply - YASKAWA

CPS-150F - Power Supply - YASKAWA

CPS-150F

This YASKAWA/YASNAC CN05 and CPS-150F Power Supply is used for the NX100 and XRC MOTOMAN series.

Input voltage - 200-230 V AC, frequency - 50/60 Hz, current - 2.1 A

This CPS-150F power supply is at your disposal to replace your defective equipment and has a guarantee of operation adapted to your needs.

State
  • Refurbished Supply
Warranty
€695.00

System options

Exchange service with a refurbished unit

Standard Exchange Service

Reconditioned and tested systems

From 6 to 12
month warranty

Exchange service with a new unit

Standard Exchange Service

New systems

From 12 to 24
month warranty

Supply of a refurbished unit

Supply Service

Reconditioned and tested systems

From 6 to 12
month warranty

Supply of a new unit

Supply Service

New systems

From 12 to 24
month warranty

For parts only

Supply Service

Sold for parts – no warranty

Repair

Repair service

Repair will be made to damaged and defectiv units

From 3 to 18
month warranty

Livraison rapide

Fast
delivery

Livraison rapide

guaranteed
products

Livraison rapide

Secure
payment

 

Control Power Supply Unit (CPS-150F)
This unit supplies the DC power (DC5V, 24V) to the I/O contactor unit (JZNC-XIU 01) and the programming pendant. It is also equipped with the input function for turning the control power supply on and off.

1. Disconnect all cables connected to the control power unit.
2. Undo four upper and lower screws attaching the control power unit and the rack. (two
screws on each side).
3. Pull out the control power unit from the rack holding the lever which is attached at the
upper and lower side.
4. Insert the new control power unit in to the slot of the rack.
5. Push the new control power unit until it is placed in the same position of other boards.
6. Tighten upper and lower screws.
7. Connect all disconnected cables.

System Control Circuit Board (JANCD-XCP01)
This board performs to control the entire system, display to the programming pendant, control the operating keys, control operation, calculate interpolation, and interface the servo control circuit board (with a serial communication board JANCD-XIF03 or JANCD-XIF04). This board has the PC card interface and Serial interface for RS-232C. The JANCD-XMM 01 board (option) can be installed when CMOS memory is expanded.

Height
6 cm / 2,3 in
Width
19 cm / 7,4 in
Length
27 cm / 10,6 in
Weight
1,4 kg / 3 lbs
Family
MOTOMAN XRC 2001 CONTROLLER
Reference
CPS-150F
Refurbished
3005714884318
300166127628

Yaskawa The company was founded in 1915 and its headquarters is located in Kitakyushu, Japan.

The company is the world leading manufacturer of servo motors, converters, axis drives and control systems used in industrial automation, and Motoman robots.

12 other products in the same category:

www.standard-exchange-industry.com is getting a new look !

We are tweaking the last settings, in the meantime the orders are temporarily disabled.

However, don't hesitate to check out our new website!

For all information, contact us by e-mail on contact@standard-exchange-industry.com or by phone on +33 3 24 52 97 66